How do I make a mold box?
Posted on 7/28/2014
The purpose of a mold box is to contain the liquid rubber (after it is poured over and around a model) until the liquid turns to a solid. A mold box does not have to be a complex structure -depending on the size and configuration of your model, often a coffee can, cake pan or plastic bucket will suffice. If you make molds of flat – two dimensional models on a regular basis and require a mold box there are a number of advantages in constructing your own mold box.
Advantages of Constructing A Mold Box
* Easy To Construct
* Minimal Assembly Required
* Adjustable (to adapt to different size models)
Original Model Used In This Presentation: Terra Cotta Cameo Decorative Plate.
Dimensions: 15″ long x 10.5″ wide x 1″ tall (38 cm x 27 cm x 2.5 cm)
Flat Baseboard — (Plywood or Acrylic Sheeting)
Dimensions: 20″ long x 16″ wide x ½ ” thick (51 cm x 41 cm 1.3 cm)
Retaining Pieces- (4) 2″ x 3″ (5 cm x 7.6 cm pieces of wood or acrylic)
(4) 2″ x 22″ (5 cm x 56 cm pieces of wood or acrylic)
Screws: 1″ (2.5 cm) Clamps
Hot melt glue gun
Step 1. Cut and Assemble Retaining Walls
To accommodate our model, we have constructed retaining walls out of ½” (1.3 cm) thick acrylic strips. We selected acrylic because most mold rubbers release easily from acrylic. Wood can also be used. Four pieces measuring 2″ x 3″ (5 cm x 7.6 cm) were cut for the shorter side of the retaining wall and four 2″ x 22″ (5 cm x 56 cm) pieces were cut for the longer side of the retaining
wall. These pieces were then assembled together in an “L” shape with 1″ (2.5 cm) screws. (See Figure One Below).
Step 2. Secure Model To Baseboard
The baseboard should be at least twice the size of the original model to allow enough “working space”. Secure the model to the backboard by applying a bead of hot melt glue around the perimeter of the reverse side of the model. Press model firmly onto baseboard and create a tight seal where the model meets the baseboard. This will prevent liquid rubber from leaking underneath the model.
Step 3. Assemble Retaining Walls Around Model
Place retaining pieces around the model, making certain there is at least a ½” (1.3 cm) clearance (gap) between the cameo and retaining wall. This ½” (1.3 cm) gap will equal the wall thickness of the cured rubber mold. (Figure Two)
Step 4. Clamp Retaining Walls Together
Fasten the retaining walls together with C-clamps and apply hot melt glue to any seams where the liquid rubber may leak out. This includes seams where the retaining walls meet the baseboard and also where retaining walls meet one another. Important: Mold box seams not properly sealed will result in rubber leakage – which equals lost time, dollars and material. (Figure Three)
Step 5. Apply Sealer To Model: Smooth-On SUPERSEAL.
Being made of terra cotta, the cameo and any other porous model must be sealed. Models made of water/sulfur based clays must also be sealed as well. Apply 2 coats of SuperSeal to entire model and surrounding forms (let first coat dry 7 minutes before applying next coat, letting final coat dry for at least 1 hour).
Step 6. Apply Release Agent – Smooth-On Universal Mold Release.
For easiest release, apply Universal Mold Release after SuperSeal is dry. Spray a light mist coating over surface of model and surrounding forms. Brush over surface and into areas of detail. Follow with another light mist coating and let dry for 15 minutes before applying rubber.
Step 7. Pour Mold Rubber
Mix and pour mold rubber onto model and let cure. Be certain that the liquid rubber levels off at least ½” (1.3 cm) above the highest point on the model. Let rubber cure overnight.
Step 8. Removal of Retaining Walls.
Finally, after rubber has cured, remove the retaining walls away from the cured mold and flex rubber mold to remove original model. (Figure Four)
Step 9. Demold.
Remove cameo from the cured rubber.
Constructing a Simple Mold Box
The FAQ list is offered as a guideline and offers possible solutions to problems encountered during mold making and casting. No warranty is implied and it is up to the end user to determine suitability for any specific application. Always refer to the provided Technical Bulletins (TB) & Material Safety Data Sheets (MSDS) before using any material. A small scale test is suggested to determine suitability of any recommendation before trying on a larger scale for any application.