| Sculptex® Non-Toxic Modeling Clay |
Sculptex® Non-Toxic Modeling Clay
|
Sculptex® is a non-toxic, non hardening modeling clay that is sulfur-free and non contaminating. Sculptex® is an ideal alternative to sulfur-based clays, which are incompatible with some mold rubbers. It holds excellent detail and is great for precision sculpting, prototyping and model making. Sculptors who have used Sculptex® say that it's the perfect replacement for Klean Klay.
- Sculptex® is available in SOFT, MEDIUM, & HARD
|
|
 |
|
| Mixing Containers |
Mixing Containers
|
Plastic mixing containers with graduated markings for accurate measurement of materials which are measured by volume.
Available in 16 oz., 32oz., 64 oz., and 165 oz. sizes. Packaged in cases of 10 or 100 containers. |
|
|
|
| EpoxAmite® Dispensing Pumps |
EpoxAmite® Dispensing Pumps
|
EpoxAmite® pumps are calibrated to deliver the correct amount of Part A resin and Part B hardener with a single push.
One Push ‘A' + One Push ‘B' = Correct Amount of Product to Mix.
No need to weigh components using a gram scale or measure by volume using graduated cups. Pumps are identified by label on pump head.
Note: These pumps are for EpoxAmite® laminating resins ONLY
|
|
|
|
| Mechanical Mixers |
Mechanical Mixers
|
The Turbine Mixer is a simple design, yet does a better job of mixing rubbers, plastics and foams than any mixer we've tried.It also mixes powder-based Alja Safe™ alginate and Matrix NEO™ with fiber better than any other mixer. Just as important; it is easier to clean vs other mixers that we've tried saving time and labor. The Turbine Mixer is also less expensive vs. other mixers on the market. |
|
|
|
| Kwikee™ Non-Aerosol Sprayer |
Kwikee™ Non-Aerosol Sprayer
|
The Kwikee™ sprayer is an economical alternative to aerosols for dispensing release agents and sealing agents. It is a faster, labor-saving way to cover large models or molds and delivers sealing agent or release agent in a fine mist. |
|
|
|
| Dispensing Guns and Accessories |
Dispensing Guns and Accessories
|
Dispensing guns hold Body Double™, Dragon Skin™, Ecoflex™ and other 400 ml cartridges and forces the Parts A & B through a static mixing tube. Squeeze the handles of the manual gun, pull the trigger on the electric gun. The electric gun is excellent for frequent molders and larger projects. |
|
|
|
| E-Z Spray Jr. Gun and Accessories |
E-Z Spray Jr. Gun and Accessories
|
EZ-Spray® Jr. Spray Gun - The EZ-Spray® Jr. is a versatile, convenient and easy-to-use spray system for spraying moldmaking and casting materials.
The following accessories are available for the EZ-Spray® Jr. spray system.
EZ-Spray® Jr LARGE Mixing Tubes - Static mixers for EZ-Spray® Silicone 20 and EZ-Spray® Silicone 35.
EZ-Spray® Jr SMALL Mixing Tubes - Static mixers for EZ-Spray® STYROCOAT, EZ-Spray® Foam, and EZ-Spray® 45
EZ-Spray® Jr Small Spray Tip Assembly - This assembly is inserted on the end of a SMALL EZ-Spray® Jr.static mixer.
EZ-Spray® Jr. Large Mixer Adapter - This adapter is REQUIRED to use the large static mixers for the EZ-Spray® Jr. system.
|
|
|
|
| Vacuum Chambers |
Vacuum Chambers
|
Vacuum Chambers For Vacuuming Liquid Rubbers and Liquid Plastics
Vacuum systems (vacuum chamber and vacuum pump that pulls 29 inches of mercury) are used to remove the air from high viscosity materials like silicone rubber before pouring. They are also ideal for vacuum degassing liquid plastics (such as Crystal Clear® plastic) for making bubble free castings. Easy to read gauge let's you know if your vacuum pump is pulling the required 29" of mercury.
Vacuum pump not included. |
|
|
|
| Pressure Chamber |
Pressure Chamber
|
Versatile Unit for Pressure Casting Liquid Rubber and Liquid Plastics. Pressure casting resins is optimal for creating castings that are truly bubble free. Recommended Pressure for Pressure Casting; 60 psi. Can be pressurized to 80 psi. Inside Dimensions:
12.5" (31.75 cm) diameter opening X 15.25" (38.74 cm) Tall Compressor Not Included For usage instructions, refer to the Technical Bulletin. |
|
|
|
| E-POX-EE KLEENER™ Hand Cleaner |
E-POX-EE KLEENER™ Hand Cleaner
|
E-POX-EE KLEENER™ is a unique industrial hand cleaner made especially for removing unreacted liquid epoxy, polyester, urethanes and other resins from the skin. It will also remove liquid paint, lacquer and grease. Directions for Best Results -
DO NOT WET HANDS BEFORE USING
1. Dispense a liberal amount of Kleener onto the hands.
2. Work well into resin contaminated areas.
3. Wash hands with soap and water.
4. Repeat as necessary. Safety First! For Industrial Use Only - Keep Away From Children |
|
|
|
